| Philips HeartStart Defibrillators |
 |
| Philips Defibrillators give you the power to save lives... anywhere, any place, any time
The current national survival rate for sudden cardiac arrest is less than five percent
The likelihood of successful resuscitation decreases by about 10% with every minute that passes
An additional 40,000 lives could be saved each year in the U.S. alone with widespread access to defibrillators
|
|
Philips Heart Start Carrying Cases |
Philips M5075A
|
Standard Carrying Case for HeartStart OnSite
The standard carry case is constructed with semi-rigid materials and covered in durable red cordura. The case comes equipped with a pair of paramedic scissors and can accommodate one spare pad cartridge and a spare battery pack.
Dimensions: 9.5" (24 cm) W x 8.5" (21 cm) H x 4.8" (12cm) D
Material: Codura
Use with : HeartStart OnSite (M5066A)
|
|
|
Philips M5076A
|
Slim Carrying Case for HeartStart OnSite
This slim carry case is constructed with semi-rigid materials and covered in durable red cordura. The case holds the HeartStart OnSite Defibrillator and a pair of paramedic scissors.
Dimensions: 9.5" (124 cm) W x 8.5" (21 cm) H x 4.8" (9 cm) D
Material: Codura
Use with : HeartStart OnSite (M5066A)
|
|
|
Philips M3868A
|
Vinyl Carrying Case for HeartStart FR2
A red cordura, semi-rigid carrying case is available to hold the device as well as spare battery and up to 3 sets of pads.
Dimensions: 11" W x 9" H x 5" D
Use with : HeartStart FR2+ (M3861A & M3862A) |
|
|
Philips 989803139251
|
Carrying Case for HeartStart FRx
The rugged FRx carry case made of wipeable urethane was designed to hold the FRx defibrillator as well as its main accessories and supplies. The carrying case is intended for use in environments where the defibrillator is protected from moisture and harsh treatment
Use with : HeartStart FRx (861304) |
|
|
Philips 989803133171
|
Temperature Controlled Carrying Case for HeartStart FR2 Plus
With the Philips Temperature Control Carrying Case, you can safely store your HeartStart FR2-series Defibrillator in the trunk or storage compartment of a vehicle during extreme winter and summer temperatures. It provides protection from temperatures as low as –20°F (-29ºC) and as high as 140°F (60ºC), perfect for utility trucks, police cruisers and other vehicles in which heating or air conditioning isn’t always available. The case’s thermostat-regulated heater can be powered by a 12-volt vehicle battery, while the built-in cut-off module turns off the heater before it depletes the battery. And a thick foam insulation layer slows the heating effect of hot summer days
For Use with: HeartStart FR2+ (M3861A & M3862A) |
|
|
Philips HeartStart Batteries |
Philips M5070A |
HeartStart Four-Year Battery
This battery is a disposable, lithium manganese dioxide, long-life battery that will typically last for four years with the defibrillator in standby mode.
Shelf Life: Typically 4 years with defibrillator in standby mode.
For Use with: HeartStart OnSite (M5066A), HeartStart FRX (861304)
|
|
|
Philips M3863A |
FR2+ Long Life LiMnO2 Battery
Lithiumm manganese battery. Disposable, recyclable, long life.
Battery Life: Minimum 300 shocks or 12 hours operating time
Standby Life: 4 years minimum, 5 years typical when battery is installed by the Install-By-Date
For Use with: HeartStart FR2+ (M3861A & M3862A)
|
|
|
Philips M3848A |
FR2+ Rechargeable Li Ion Battery
In hospital and EMS environments, where the useful life of a defibrillator's disposable battery can be consumed in a relatively short period of time, the FR2+ Rechargeable Battery (M3848A) provides a cost-effective option for frequent-use applications, such as back-to-back sudden cardiac arrest responses and monitoring patients during transport.
This Lithium-Ion battery is fully charged (using the Charger M3849A) in just 3 hours to provide 100 shocks (typical) or 5 hours (typical) of ECG display time. The "fuel gauge" on the FR2+ displays the battery's remaining power. Under normal conditions, the FR2+ Rechargeable Battery withstands 300 charge-discharge cycles or 2.5 years of use.
Standby Life: 6 months
For Use with: HeartStart FR2+ (M3861A & M3862A)
|
|
|
Philips M3849A |
FR2+ Battery Charger for Rechargeable Li Ion Battery
In hospital and EMS environments, where the useful life of a defibrillator's disposable battery can be consumed in a relatively short period of time, the Rechargeable Battery (M3848A) provides a cost-effective option for frequent-use applications, such as back-to-back sudden cardiac arrest responses and monitoring patients during transport.
This Lithium-Ion battery is fully charged (using the Charger M3849A) in just 3 hours to provide 100 shocks (typical) or 5 hours (typical) of ECG display time. The "fuel gauge" on the FR2+ displays the battery's remaining power. Under normal conditions, the Rechargeable Battery withstands 300 charge-discharge cycles or 2.5.years of use.
For Use with: HeartStart FR2+ (M3861A & M3862A)
|
|
|
Philips 989803139301 |
FRX Aviation Battery
For Aircraft Use. Philips replacement Lithium Ion 4-Year Battery for the FRx AED. Delivered to you with Philips' 4-year warranty and 200+ shock capacity, just like your original battery pack. Complies with TSO C-142
Use with : HeartStart FRx (861304)
|
|
|
Philips 989803136291 |
FR2 Plus Aviation Battery
For Aircraft Use. Philips replacement Lithium Ion 4-Year Battery for the FR2 Plus AED. Delivered to you with Philips' 4-year warranty and 200+ shock capacity, just like your original battery pack. Complies with TSO C-142
For Use with: HeartStart FR2+ (M3861A & M3862A)
|
|
|
Philips HeartStart Cabinets |
Philips 989803136531 |
Basic Defibrillator Cabinet
Basic audible siren alarm.
No visual alarm or connectivity to building’s security system
For Use with: HeartStart OnSite (M5066A), HeartStart FR2+ (M3861A & M3862A), HeartStart FRX (861304)
|
|
|
Philips PFE7024D |
Defibrillator Cabinet (surface mount)
The Defibrillator Cabinet, constructed of heavy gauge steel and tempered glass, protects your defibrillator from theft and the elements. Equipped with an audible alarm and flashing lights (powered by two 9-volt alkaline batteries), the Cabinet attracts attention to mobilize assistance during a cardiac emergency or deter theft. Opening the Cabinet's door activates the audible alarm and lights. For locations where a siren is inappropriate, the audible alarm can be disabled.
In buildings with a central security system, your facilities people, or alarm company, can connect the cabinet alarm to your system for a more coordinated response to a cardiac emergency. The alarm can also be connected to a programmable auto-dialer.
The Cabinet is available in two styles: a wall surface mounted Cabinet, for easy installation without cutting into walls, and a semi-recessed model, that is inserted into a wall cut-out, for a less obtrusive look. The semi-recessed model is appropriate where Americans with Disabilities Act (ADA) regulations are a consideration.*
Dimensions: 16" x 22.5" x 6"
* The Americans with Disabilities Act requires that objects not protrude more than 4 inches into foot traffic areas of open aisles and walkways unless the object's bottom edge is no higher than 27 inches from the ground.
For Use with: HeartStart OnSite (M5066A), HeartStart FR2+ (M3861A & M3862A)
|
|
|
Philips PFE7023D |
Defibrillator Cabinet (semi-recessed)
The Defibrillator Cabinet, constructed of heavy gauge steel and tempered glass, protects your defibrillator from theft and the elements. Equipped with an audible alarm and flashing lights (powered by two 9-volt alkaline batteries), the Cabinet attracts attention to mobilize assistance during a cardiac emergency or deter theft. Opening the Cabinet's door activates the audible alarm and lights. For locations where a siren is inappropriate, the audible alarm can be disabled.
In buildings with a central security system, your facilities people, or alarm company, can connect the cabinet alarm to your system for a more coordinated response to a cardiac emergency. The alarm can also be connected to a programmable auto-dialer.
The Cabinet is available in two styles: a wall surface mounted Cabinet, for easy installation without cutting into walls, and a semi-recessed model, that is inserted into a wall cut-out, for a less obtrusive look. The semi-recessed model is appropriate where Americans with Disabilities Act (ADA) regulations are a consideration.*
Dimensions: Inside compartment: 14" x 22.5" x 6", footprint on wall: 16.5" x 24.5" x 2.5" (meets ADA guidelines)
* The Americans with Disabilities Act requires that objects not protrude more than 4 inches into foot traffic areas of open aisles and walkways unless the object's bottom edge is no higher than 27 inches from the ground.
For Use with: HeartStart OnSite (M5066A), HeartStart FR2+ (M3861A & M3862A) |
|
|
Philips M3857A
Secure Seal M3859A (sold in packs of 10)
|
Wall Mount Bracket
The wall mount bracket is designed specifically for housing the Philips Heart Start defibrillator and its accessories. HeartStart OnSite's carrying case can be tethered to the wall mount bracket with the Secure Pull Seal (M3859A) to discourage tampering. A broken seal indicates that the defibrillator has been removed from the Wall Mount and accessories may need to be replenished.
Dimensions: 10.6" W x 8" H x 5" D
Use with : HeartStart OnSite (M5066A) |
|
|
Philips M3858A |
Wall Sign
An AED Wall Sign hanging above a wall mount bracket or defibrillator cabinet gives even greater visibility to the defibrillator. Dimensions: 7" W x 10" H |
|
|
Philips M3854A |
Data Card & Tray
The Philips data card holds approximately 8 hours of incident and ECG information, or one hour with voice recording. One card can hold data from multiple cases. A flash data card reader enables data transfer from the card to a personal computer for use with Philips HeartStart Event Review data management software.
For Use with: HeartStart FR2+ (M3861A & M3862A)
|
|
|
| Philips HeartStart Defibrillator Pads |
Philips DP2 & DP6 |
Adult AED Defibrillator Pads: DP2 / DP6
HeartStart Adult AED Defibrillator Pads, 2- or 6-pack recommended for patients 8-years and older, or above 55 pounds (25kg), are optimized for AED use with Philips FR2-series defibrillators. Constructed of a thin flexible conductor sandwiched between a protective polymer backing and a hydro-gel adhesive, these pads withstand the rigors of CPR and harsh conditions. Soft, flexible and oval shaped, HeartStart Adult AED Pads conform to body contours for ample surface contact and adhesion. The robust lead wire connector is ergonomically designed, enabling fast and easy insertion.
Minimum Shelf Life: 24 months from date of manufacture
For Use with: HeartStart FR2+ (M3861A & M3862A) |
|
|
Philips M3870A |
Infant/Child AED Defibrillator Pads
Infant/Child Reduced-Energy Defibrillator Pads enable minimally trained responders to safely and promptly defibrillate infants and children under 8 years of age or 55 pounds. These special infant/child pads contain electronics that attenuate, or reduce, the energy of the defibrillator's shock from 150 to 50 Joules, an appropriate dosage of SMART Biphasic therapy for infants and small children.* And the FR2-series defibrillator can evaluate children's heart rhythms with outstanding accuracy for appropriate shock/no-shock decisions.**
The pads' design was carefully thought out to ensure that, even for the most inexperienced user under the most stressful circumstances, it is instantly obvious that these pads are for children and infants only. This helps ensure that the correct pads are chosen when you need to be prepared to treat both adults and children. The packaging, graphics, and pink teddy bear-shaped connector clearly communicate pediatric use.
Minimum Shelf Life: 24 months from date of manufacture
For Use with: HeartStart FR2+ (M3861A & M3862A) |
|
|
Philips M5071A
|
Adult SMART Pads Cartridge for HeartStart OnSite
HeartStart Adult SMART Pads are appropriate for cardiac arrest victims 8 years and older, or weighing above 55 pounds (25kg) or more
Shelf Life: Replace every two years
Use with : HeartStart OnSite (M5066A)
|
|
|
Philips 989803139261
|
SMART Pads II for HeartStart FRx
Multifunction defibrillator pads
Use with : HeartStart FRx (861304) |
|
|
Philips M5072A
|
Infant/Child SMART Pads for HeartStart AED
Infant/Child Cartridge - Spare Electrode Pads for Philips HeartStart OnSite AED
Use with : HeartStart OnSite (M5066A) |
|
|
Philips HeartStart Miscellaneous Accessories |
Philips 989803139311
|
Infant / Child Key for HeartStart FRx
Infant/child key used in infant/child defibrillation with the HeartStart FRx Defibrillator. Simply insert the Infant/Child Key into the FRx to signal to the device that you’re treating an infant or a child. The defibrillator adjusts to provide special pads placement and CPR instructions. The pads icons also flash to show you the appropriate pads placement and the device reduces the shock energy to a level more appropriate for an infant or a child (less than 55 pounds or 8 years of age).
Use with : HeartStart FRx (861304)
|
|
|
Philips 68-PCHAT |
Fast Response Kit
The Fast Response Kit contains tools and supplies typically needed for patient care and personal protection: 2 pairs of hypoallergenic nitrile gloves, a Laerdal pocket breathing mask, paramedic scissors, a Gallant chest hair razor, and a large extra-absorbent paper towel. These items are contained in a 5-1/2" x 9-1/2" zippered pouch which can be attached to the handle of the semi-rigid or vinyl carrying cases.
Contains: 2 pairs of nitrile gloves, 1 CPR mask, 1 paramedic scissors, 1 prep razor, 1 large reinforced paper towel, 1 zippered pouch
Use with : HeartStart OnSite (M5066A), HeartStart FR2 (M3861A & M3862A)
|
|
|
Philips M5066-97800 |
Quick Reference Guide - $5
The Quick Reference Guide is a brief instruction guide for defibrillator operators. Its short captions and straightforward drawings break down each step of the defibrillation process.
Use with : HeartStart OnSite (M5066A) |
|
|
